For a six-seat dining table, look for a slab, or a bookmatched pair, about 6 to 7 feet long and 36 to 42 inches wide, and plan on finishing it around 1½ to 2½ inches thick. A coffee table or desk needs much less. Below are the common sizes, when to join two slabs instead of hunting for one wide one, and what to look for in the wood itself.
Size chart by table type and seats
The usual guideline is about 24 inches of table edge per seated person. These are common sizes, not rules. Measure your room and the chairs you'll use.
| Table | Seats | Common length | Common width | Common height |
|---|---|---|---|---|
| Dining | 4 | 48–60 in | 30–40 in | 30 in |
| Dining | 6 | 72–84 in | 36–42 in | 30 in |
| Dining | 8 | 96–108 in | 36–42 in | 30 in |
| Dining | 10 | 120 in and up | 40–44 in | 30 in |
| Kitchen or breakfast | 2–4 | 36–48 in | 30–36 in | 30 in |
| Coffee table | n/a | 36–60 in | 18–30 in | 16–18 in |
| Desk | 1 | 48–72 in | 24–30 in | 29–30 in |
| Console or sofa table | n/a | 48–72 in | 12–18 in | 30 in |
| Bench | 2–4 | 48–72 in | 12–16 in | 17–18 in |
Three things to keep in mind when you hold a slab up against this chart:
- Measure the narrow end. A live edge slab is wider at one end than the other. The narrow point sets how many people fit comfortably.
- The edge isn't all usable. Sapwood, bark and a wavy edge eat a few inches. Measure from solid wood to solid wood.
- Leave length for trimming. Slab ends often have small checks from drying. Buy a few inches longer than your finished length so they can be cut off.
One wide slab or a bookmatched pair
A single slab wide enough for a dining table has to come from a big tree. Those slabs exist, but they're the most expensive pieces on any rack, and wide slabs move more as they dry.
The usual answer is a bookmatched pair: two consecutive cuts from one log, opened like a book and joined along a straight center seam. The grain mirrors across the middle. Two 18-inch slabs make a 36-inch top from a tree that could never give a 36-inch slab.
How to choose:
- One slab if you want an unbroken top, the tree was big enough, and the budget allows.
- A bookmatched pair for standard dining widths, a symmetrical look, or species that rarely grow wide, like cherry.
- Two slabs with a gap if you want a river table (below).
Thickness after flattening
A slab you buy rough is thicker than the top it becomes. Drying leaves most slabs a little cupped or twisted, and flattening both faces takes that out. The more a slab has moved, the more thickness comes off.
Common guidelines:
- Dining tables: most finish somewhere between about 1½ and 2½ inches. Thicker looks heavier and costs more; thinner can look flimsy on a long span.
- Coffee tables and desks: 1½ to 2 inches is typical.
- Benches: 2 inches or more, since people sit on them.
Buy a rough slab thicker than the finished thickness you want. Our guide to flattening a slab with a router sled shows how it's done at home.
River tables: what to look for in a slab
An epoxy river table uses two slabs with their live edges facing each other and a pour of epoxy between them. What matters in the wood:
- Dryness. Epoxy doesn't stop wood from moving. A wet slab shrinks after the pour and can crack the epoxy or pull away from it.
- Interesting edges. The edge is the whole point. Curves, bumps and a crotch all read well in a river.
- Matching thickness and color. Slabs from the same log, ideally a bookmatched pair, look like they belong together.
- Sound wood along the edge. Soft or loose sapwood and bark should come off before the pour.
Our guide on choosing a slab for an epoxy river table goes deeper.
Cracks, bark and voids
Almost every slab has some of these. Most are character, not a defect.
- End checks. Short cracks at the ends from drying. Normal; they usually trim off.
- Through cracks. A crack that runs deep into the slab needs to be stabilized with bow ties (butterfly keys) or filled with epoxy before it's a tabletop. See bow ties and epoxy fills for slab cracks.
- Bark. Bark on a dried slab often loosens over time. Some people peel it and keep the shape of the wood underneath; others glue it down. For how to do either, see keeping the bark on a live edge.
- Knots and voids. Small voids fill well with tinted epoxy. A loose knot needs to be glued or filled.
What to avoid: soft, punky wood you can dent with a thumbnail, active insect holes with fresh sawdust, and a slab still green enough to be cold and damp to the touch if you need it built soon. Our guide on why slabs crack and cup explains which cracks matter.
Slabs that fit
Measure your space, pick a table type from the chart, and decide whether you want one slab or a pair. Then check the slabs page or send us the size.
Not sure which wood? Our slab species comparison lines up color, hardness and price, and the pricing page shows how to estimate a slab's cost from its size.
Ask About a Slab
Send us the table type, the finished length and width, and the species you're leaning toward. We'll pick out slabs, or pairs, sized for it.