Slabs crack and cup because wood shrinks as it dries, and it doesn't shrink evenly. It shrinks about twice as much along the growth rings as across them, and the outside dries before the inside. Those uneven forces pull the wood apart at its weakest points and bend it across its width.
Most cracks in a slab are harmless: end checks that get trimmed off, or small surface checks that close up or fill. The cracks that matter run through the full thickness, start at the pith, or are still growing. Here's how to tell them apart.
Why wood shrinks unevenly
Wood doesn't shrink until it drops below the point where the cell walls start giving up water. From there down, it shrinks as it dries and swells again if it picks moisture back up.
The USDA Forest Products Laboratory's Wood Handbook puts it simply: wood shrinks most in the direction of the growth rings, about half as much across the rings, and only slightly along the grain (Wood Handbook, Chapter 4). A slab is a cross-section of a tree, so it has growth rings curving through it in every direction. Different parts of the same slab want to shrink by different amounts.
Timing adds a second problem. The surface and the ends dry first. The Wood Handbook notes that the surface starts shrinking while the inside can still be quite wet. The dry outer layer wants to get smaller, the wet core won't let it, and the surface splits.
Why slabs cup
Cupping is when a slab bends across its width so one face is concave and the other is convex.
On a flat-sawn slab, the growth rings show as arcs on the end. As the slab dries, those arcs try to straighten out, because the wood shrinks more along the rings than across them. The face that was closer to the bark ends up concave. The Wood Handbook's figure on shrinkage and distortion shows the same pattern in boards.
A slab that cups after it's dry and flat is almost always a slab that wasn't finished drying, or one that's picking up or losing moisture unevenly. That happens when only one face is finished, when one face sits on a damp floor, or when sun hits one side.
Twist and bow come from the same shrinking forces, made worse by wild grain, crotches and wood from a leaning trunk.
The cracks you'll see, and what each means
End checks. Short cracks at the ends of the slab. End grain dries fastest, so nearly every air-dried slab has some. They're usually cosmetic. Most get trimmed off when the slab is cut to length.
Surface checks. Fine, shallow cracks on the face, often along the rays in oak. They come from the surface drying faster than the core. Many close partway once the slab dries through, and flattening removes some of them. The rest sand out or fill.
Pith cracks. Slabs cut through the center of the log include the pith, the small soft core of the tree. Wood around the pith shrinks unevenly, so these slabs very often crack outward from it. A pith crack can run a long way and through the full thickness. Center slabs are often the widest and best-looking, so plenty of people buy them anyway and stabilize the crack.
Through-cracks and splits. Cracks you can see on both faces. These are the ones to look at closely. Some are stable and make a slab look better once they're filled. Others are still opening.
Shake. Separation along a growth ring, so a layer of wood is loose from the next. It usually starts in the standing tree, not in drying. Shake is hard to stabilize and can let a piece of the slab come loose. On a tabletop it's usually a cut-off or a deal-breaker.
Honeycomb. Internal cracks you can't see from the surface, caused by drying too hard and fast. MU Extension describes it as a result of extreme drying (MU Extension G5507). You may not find it until you flatten the slab or cut it. It's rare in slowly air-dried wood.
Which cracks matter
Ask four questions about any crack.
1. Is it still moving? This is the big one. A crack in a dry slab that has stopped growing is a design feature you can fill or tie. A crack in a wet slab will keep opening. Look for clean, bright wood inside a crack (recent) versus gray, weathered, dusty wood (old). Mark the tip with a pencil and check it again in a few weeks if you can.
2. Does it go through? A surface check that stops partway is cosmetic. A crack you can see on both faces affects the slab's strength across that line.
3. Where is it? A crack near the end can usually be cut off. A crack running down the middle of a slab you need at full length has to stay and be stabilized.
4. Is it in the part you're keeping? Plan your cuts before you judge the slab. A slab with a bad end and a clean middle may give you exactly the piece you need.
If the answers are "no longer moving," "partway," and "in a part you can cut off or live with," the crack isn't a problem.
How to keep a dry slab from cracking or cupping later
Most of this comes down to letting the slab stay in balance with the air around it.
- Start dry. Buy a slab that's dry enough for where it's going, or let it settle indoors until a meter shows it has stopped losing moisture. Our guide on how to check whether a slab is dry covers that.
- Flatten after it settles, not before. A slab flattened while it's still drying will move again. Doing it yourself? The router sled guide.
- Finish both faces. A common rule among furniture makers is to finish the underside too, so both faces take on and give up moisture at a similar rate. One-sided finishing is a common cause of cupping.
- Let the top move on its base. Fasten a slab top with hardware that allows seasonal movement across the width, such as slotted holes or tabletop fasteners, rather than screwing it down tight. A top that can't move will crack instead.
- Keep it out of extremes. Direct sun on one face, a heat register blowing on one side, or a damp basement floor all dry or wet one part faster than another.
Cracks aren't always a defect
Plenty of slab buyers want character. A stable crack filled with epoxy or crossed with a couple of contrasting bow ties is one of the reasons people buy a live edge table instead of a flat-pack one. Price usually reflects cracks too, so a cracked slab can be a better buy if you like the look.
Our guide to bow ties, epoxy fills and other ways to stabilize a split covers the fixes. For how cracks and dryness affect price, see our pricing page.
Ask About a Slab
Ask us about any crack on a slab you're considering: how long it's been there, whether it goes through, and where you could cut around it.