Straight answers to the questions slab buyers ask us most. If yours isn't here, send it with the request form.
Are your slabs dry?
It depends on the slab, and we'll tell you which before you buy. We don't kiln-dry: a slab from us is either green, fresh off the mill, or air-dried.
A green slab costs less, but give it time to dry before you build with it. A common rule of thumb for air drying is about one year per inch of thickness, and thick or dense slabs often take longer. See how long a slab takes to dry.
What moisture content should a slab be?
For indoor furniture, close to the moisture content wood settles at inside your house. MU Extension puts wood used indoors in Missouri at about 6 to 10%, and air-dried lumber at about 12 to 14% (MU Extension G5507).
An air-dried slab is dry enough to flatten and work, but expect it to lose a little more moisture indoors. Let it sit inside for a while before final flattening and finishing. Our guide on how to check if a slab is dry explains meters, weighing and what to look for.
Will it crack?
Probably a little, and that's usually fine. Most slabs have some end checks from drying, and a slab can open small cracks as it adjusts to a heated house. Cracks that run deep or keep growing should be stabilized with bow ties or epoxy before the slab becomes a tabletop.
Sealing all faces and the ends evenly, and not building with a wet slab, prevents most problems. See why slabs crack and cup and bow ties and epoxy fills for slab cracks.
Will the bark stay on?
Sometimes, but don't count on it. Bark tends to come loose as a slab dries, especially on trees cut in spring and summer when the layer under the bark is active. Many people peel it and finish the wood underneath, which keeps the natural shape. If you want the bark, it can be glued down with thin CA glue or epoxy. Our guide to keeping the bark on a live edge covers both.
How thick should a table slab be?
For a dining table, plan on roughly 1½ to 2½ inches once it's flat and finished; coffee tables and desks can be a bit thinner. Since flattening removes wood, start with a rough slab that has some thickness to spare. Our page on choosing a slab for a table has a size chart by table type.
Can you cut a slab to length?
Ask us when you pick out the slab. Whatever length you settle on, add a few inches so the checked ends can be trimmed off.
Can I come look at the slabs?
Ask us first. Slabs move on and off the racks, so send the size and species you want before you make the drive.
Do you deliver?
Plan on picking up at our yard near Columbia, with a second pair of hands and a truck bed or trailer that lets the slab lie flat.
Will you hold a slab for me?
Ask when you send the slab ID. Slabs are one of a kind, so if you've found the one, tell us soon.
Do you have bookmatched pairs?
Ask us; pairs depend on the log. Neighboring cuts from one log, laid open side by side, give a mirrored grain pattern across the seam. That's the usual way to get a wide dining top or a river table. Ask for one on the request form and give the finished width you need.
How should I store a slab until I build with it?
Flat, off the ground and out of the weather, with air on both faces. Lay it on three or more evenly spaced, level supports so it doesn't sag, and keep it out of direct sun and away from a heater vent. Bring it indoors where it will live for a while before final flattening, so it settles to your house first. A slab stored leaning against a wall, or flat on a concrete floor, is likely to bow or cup.
What's the difference between a slab and a board?
A slab is a wide, thick cut through the log with at least one natural edge left on. A board is narrower and squared on all four sides. Slabs are usually sawn 2 inches thick or more so they stay stiff across their width and leave room for flattening. Because a slab keeps the shape of the tree, no two are alike, which is why each one is measured and priced on its own.
How do I pay?
We'll confirm the price and how to pay when we reply about your slab.
Can you cut a slab from my own tree?
Yes. If you have a walnut, oak or other good log from your own tree, we can saw it into slabs at our mill near Columbia. The log comes to us; we don't come to you, and we don't cut trees down. Have a tree crew fell it, ask them to leave the trunk as long logs, and bring those to our yard.
Send us the species, the diameter and length of the log, and a few photos. We'll tell you whether it's worth sawing and what it would cost.
Remember that fresh slabs from your own tree are green. Plan on drying time before they become furniture.
How do I ask about a specific slab?
Put the slab ID on the request form. Tell us your project and size if you're still looking, and we'll reply with slabs that fit.
Ask About a Slab
Send us your project, the size you need and the wood you like.