COLUMBIA
LIVE EDGE SLABS
Get a Quote

Live Edge Slab Prices

Live edge slabs are priced by the board foot. Nationally, black walnut runs about $10 to $25 a board foot, white oak and cherry about $6 to $12, and maple, sycamore, ash and elm about $4 to $10. These figures are national, not our price list. A walnut slab 8 feet long, 20 inches wide and 2 inches thick holds about 26.7 board feet, so at national prices it runs roughly $267 to $667. Every slab we sell carries its own price; the calculator at the bottom of this page estimates any size.

Price table by species

These are typical per-board-foot prices for air-dried or kiln-dried slabs, posted by slab sellers around the country. Treat them as a rough guide. National range, not our price.

Species Per board foot (national range, not our price)
Black walnut $10–$25; figured or very wide pieces higher
White oak $6–$12
Cherry $6–$12
Maple, sycamore, ash, elm $4–$10
Eastern red cedar $3–$6
Green, straight off the mill Roughly half the dried price
Flattening, both faces $75–$150 per slab, or $50–$100 per hour

Red oak and the less common woods (hickory, hackberry, honey locust, osage orange) vary more from seller to seller. Our slab species comparison shows how they rank against each other.

How board feet are measured on a slab

A board foot is a piece of wood 12 inches long, 12 inches wide and 1 inch thick, or 144 cubic inches. To get the board feet in a slab:

Board feet = length (in) × average width (in) × thickness (in) ÷ 144

Or, with length in feet: length (ft) × average width (in) × thickness (in) ÷ 12. Both give the same answer.

Because a live edge wanders, use the average width: measure the narrow point and the wide point, add them, and divide by two. Measure solid wood, not bark.

Worked examples (prices at the national ranges above, not our prices):

  1. Walnut table slab. 96 in long, 18 in at the narrow end and 22 in at the wide end, 2 in thick. Average width is (18 + 22) ÷ 2 = 20 in. 96 × 20 × 2 = 3,840 ÷ 144 = 26.7 board feet. At $10–$25: about $267 to $667.
  2. White oak bar top. 120 in long, 26 in narrow and 34 in wide, 2½ in thick. Average width 30 in. 120 × 30 × 2.5 = 9,000 ÷ 144 = 62.5 board feet. At $6–$12: about $375 to $750.
  3. Maple coffee table. 48 in long, 16 in narrow and 20 in wide, 2 in thick. Average width 18 in. 48 × 18 × 2 = 1,728 ÷ 144 = 12 board feet. At $4–$10: about $48 to $120.

Some sellers price each slab as a whole instead of by the foot, especially figured or unusual pieces. Board feet are still the fastest way to compare one slab with another.

What moves the price: width, figure, dryness, flattening

Two slabs of the same species and board feet can be priced far apart. The usual drivers:

  • Width. Slabs over about 24 inches wide come only from big trees and carry a premium per board foot. Wide slabs are rarer and harder to dry flat.
  • Length. Slabs over about 8 feet need long, straight trunks, which are less common.
  • Figure. Crotch figure, burl, curl, spalting and ray fleck all raise the price. Walnut with a crotch can cost well above the range.
  • Dryness. A dry slab is ready to work. A green slab is cheaper but you wait for it to dry. See the next section.
  • Defects. Big through cracks, rot, insect damage, wide sapwood on walnut, and heavy cup or twist lower the price.
  • Flattened or rough. Flattening both faces takes time on a router sled or wide planer and adds to the price, but saves you the work.

Ways to spend less on a slab:

  • Join two narrow slabs instead of buying one wide one. A bookmatched pair costs less per board foot than a single slab of the same width.
  • Pick a less famous species. Sycamore, ash, elm and maple make handsome tables for a fraction of walnut's price.
  • Accept some character. A slab with a filled crack, a knot or wide sapwood is usually priced lower.
  • Buy green and dry it yourself, if you have room to store it flat for a year or more.
  • Flatten it yourself with a router sled.

Green vs air-dried vs kiln-dried

What dryness means for you as a buyer:

Green. Straight off the mill, full of water. Cheapest, often around half the dried price. It will shrink, may cup or check, and has to lose that water before it becomes furniture. Air drying takes about one year per inch of thickness as a rule of thumb. Our guide on how long a slab takes to dry has more.

Air-dried. Stacked with spacers and dried outdoors or in a shed. In Missouri that usually means about 12 to 14% moisture content. That's dry enough to start working, but let it settle indoors before final flattening; it will lose a little more moisture and move a little once it's inside.

Kiln-dried. Dried in a kiln down to the range wood settles at indoors, which MU Extension puts at about 6 to 10% in Missouri (G5507). Kiln-dried slabs move the least after you build with them, and usually cost more.

Our own slabs are never kiln-dried; each one is sold as green or air-dried. Check any slab yourself with our guide on how to check if a slab is dry.

Local pickup vs shipped slabs

Online slab sellers ship nationwide, but a slab is heavy and awkward to move. Freight on a table-size slab, crated and shipped by truck, adds a real cost on top of the wood. Online, you also choose from photos.

Picking up near Columbia, you skip the freight and see the actual wood before you pay. Bring someone to help lift, plus blankets and straps for the ride home.

Slab price calculator

Enter the length, both widths and thickness of a slab, pick a species, and the calculator works out the board feet and a price range. Then send us the numbers.

Get a Quote

Tell us the length, width and wood you have in mind, or paste in the ID of a slab you liked. We'll answer with a real number for that piece.

Get a Quote

Plan your slab budget

National range, not our price. No contact details needed.

Estimate only. Figure, width over 24 inches and defects change the price. Every slab is priced individually.

Ask About a Slab ↗

MAKE ROOM FOR SOMETHING ORIGINAL

Your next project
starts with a slab.

Tell us the size, the wood and what you have in mind.

Get a Quote