You can keep the bark on a live edge if it's tight to begin with. Bark holds best on slabs from trees cut in the dormant season and dried slowly. Test it, glue down anything loose, and seal it. But on a tabletop that gets bumped and wiped every day, bark usually comes loose sooner or later, so most builders strip it and keep the natural edge shape underneath.
Here's how to decide, and how to do either one well.
Why bark comes loose
Between the bark and the wood is a thin layer of living tissue called the cambium. It's where the tree grows. In spring and summer that layer is soft and wet, and bark peels away from the wood easily. In late fall and winter, when the tree is dormant, bark is bonded more tightly.
So the time of year the tree was cut has a lot to do with whether the bark stays. That's a widely held rule among sawyers and woodworkers, though it isn't a guarantee either way.
Drying matters too. Bark and wood shrink by different amounts. A slab that dries fast can pull the wood away from the bark. Insects add a third problem: beetles and borers often work in the layer right under the bark, and their tunnels loosen it.
Should you keep the bark?
Keep it on pieces that don't get handled much: wall shelves, the back edge of a bench or console, a headboard, decorative pieces.
Strip it on dining tables, desks, bar tops and anything people will lean on, wipe down or catch a sleeve on. Bark collects crumbs and dust, wears through finish fast, and a chunk breaking off later leaves a raw patch.
Always strip it under epoxy. Bark tends to come loose inside a pour. Live edge prep for a pour is covered in choosing a slab for an epoxy river table.
The live edge is the shape of the tree, not the bark. Strip the bark carefully and you still have the curves, bumps and waves that make it a live edge slab.
How to test bark before you buy
Before you commit to keeping bark, check it the way you'd check a used car's tires:
- Press it with your thumb all along the edge. It should feel solid, not spongy or hollow.
- Tap it. A hollow sound means there's a gap behind it.
- Look at the line where bark meets wood. A visible gap or a crack along that line means it's already letting go.
- Look for small round holes or fine powder. Those are signs of insects that have worked under the bark.
- Ask when the tree was cut. Late fall or winter is better news than late spring.
If more than a few short spots are loose, plan to strip it.
How to keep it on
If the bark passes the test:
- Let the slab finish drying before you work on the bark. Gluing bark to a wet slab just delays the problem.
- Clean it. Brush off loose dirt, moss and flaking outer bark with a stiff nylon brush. Don't scrub so hard that you loosen the layers underneath.
- Glue down any loose spots. Work a thin glue into gaps along the bark line. Thin cyanoacrylate (CA) glue wicks into small cracks; wood glue injected with a syringe works for wider gaps. Clamp gently with tape or padded clamps until it sets.
- Seal it. A penetrating finish or thinned sealer soaks into the bark and binds the outer layers. Several thin coats beat one heavy one.
- Finish the rest of the slab. Use the same finish on the bark edge as the faces, or a compatible one, so the bark is protected too.
Expect to touch it up now and then. Bark that's glued and sealed lasts much longer, but it's still the softest part of the slab.
How to strip bark and keep the live edge
If the bark has to go:
- Pry off what comes off easily. On many air-dried slabs, most of the bark lifts away with a flat bar, a putty knife or a dull chisel.
- Use a drawknife or a chisel for tighter sections. Work along the edge and lift the bark, don't dig into the wood.
- Clean off the cambium layer. Under the bark is a thin, often discolored layer. Scrape it or use a stiff wire brush or a nylon abrasive brush on a drill until you reach clean, firm wood.
- Remove soft wood. Sapwood right under the bark can be punky or insect-damaged. Take it down to solid wood.
- Sand lightly. Follow the curves with a flap sander or by hand. Don't flatten the edge; the bumps and waves are the point.
A cleaned live edge takes finish beautifully. Sapwood under the bark is often lighter than the heartwood, which gives the edge a natural border. Walnut is the classic example, with pale sapwood against dark heartwood.
Bark and insects
Any slab with bark left on can hide insects that were in the tree. Many of them die out as the wood dries, but not all do, and you don't want to bring active borers into the house. Check for fresh powder (frass) under the slab or new holes that weren't there before. If you see any of those, strip the bark and talk to the seller before the slab comes inside.
Which slabs keep bark best
It depends on the tree as much as the species. Thin, smooth bark on a tree cut in winter usually holds better than thick, rough or shaggy bark cut in summer. If keeping bark matters to you, say so when you ask about a slab and ask when the log was cut.
See our page comparing Missouri slab species for how different woods look and behave as slabs, and our FAQ for more on bark.
Ask About a Slab
Let us know what the piece is for and whether you want the bark on or off. We'll help you pick a slab that suits it.