A router sled flattens a slab too wide for a planer. You set two straight rails on either side of the slab, make them level with each other, and slide a carriage holding a router across them. The router takes a shallow pass over the whole face. Repeat until the bit touches everywhere, then flip the slab and do the other side.
It's slow and loud, but it works, and you can build the whole rig from scrap and a router you already own. Here's how.
Before you start: is the slab dry?
Don't flatten a slab that's still drying. It will cup or twist again as it loses moisture, and you'll have thrown away thickness for nothing. Meter it in several spots away from the ends, and give it time indoors until repeat readings hold steady. Our guide on how to check whether a slab is dry covers how.
Fill open cracks and voids before your last passes, so one pass levels the wood and the epoxy together. Our guide to bow ties and epoxy fills covers the fill itself.
What you need
- A router strong enough to swing a large-diameter surfacing bit. Bigger routers handle this much better than trim routers.
- A surfacing bit, sometimes sold as a spoilboard or slab-flattening bit. These are wide and cut a broad, flat path.
- Two rails longer than the slab. They have to be straight and stiff enough not to sag in the middle. Straight steel or aluminum channel, a box beam, or jointed and doubled lumber all work. Check them with a straightedge before you trust them.
- A carriage that rides on the rails and holds the router. A common design is two runners joined by a base with a slot, so the router can slide side to side across the slab while the carriage moves down its length.
- A flat-enough base for the slab and rails: a sturdy bench, a sheet-goods platform, or a level section of floor.
- Shims and wedges to keep the slab from rocking.
- Clamps or screws to hold rails in place.
- Dust collection, hearing protection, eye protection and a dust mask. A router sled makes a lot of chips and fine dust.
Step 1: Set the slab so it can't rock
Lay the slab on the base with the cupped (concave) face down, so it rests on its two edges. Rock it at each corner. Wherever it moves, slip in a shim or wedge until it sits solid. A slab that moves under the router will never come out flat.
If one end is higher than the other, you don't need to fix that. The rails take care of it. You only need the slab to stay put.
Step 2: Set the rails level with each other
This is the step that decides whether the slab comes out flat.
Place a rail along each side of the slab, a little higher than the highest point of the slab's top face. The rails don't need to be perfectly level to the room. They need to be coplanar: in the same flat plane, so the carriage doesn't rock or tilt as it travels.
Ways to check:
- Lay the carriage across the rails at both ends and in the middle. It should sit without rocking anywhere.
- Use a long straightedge across the rails at several points.
- Sight across two straight sticks laid across the rails at each end ("winding sticks"). If the sticks aren't parallel, one rail is twisted relative to the other. Shim a rail end until they line up.
Fasten the rails so they can't shift. Check again after you've fastened them.
Step 3: Set the depth at the high spot
Slide the carriage over the highest point of the slab. Lower the router bit until it just touches the wood there, then lock the depth. Don't take a deep first bite. Shallow passes are easier on the router, leave a cleaner surface and are much less likely to tear out the live edge.
Step 4: Make the passes
Start at one end. Push the router across the width of the slab in a straight line, then move the carriage down the slab by a bit less than the width of the bit, so each pass overlaps the last. Work the whole length.
Tips that save trouble:
- Watch the live edge. Slow down and ease off as the bit approaches bark or a ragged edge. Loose bark and thin edge wood can tear out.
- Mind the grain direction near cracks and knots. Let the bit cut, don't force it.
- Clear chips often. A pile of chips under the carriage lifts it and throws off the cut.
- Check the router collet and bit between sessions. A big surfacing bit puts a lot of load on the router.
When the bit has touched the whole surface, lower it a little more and do another full pass. Repeat until there are no rough, untouched patches left. On a cupped slab, the center is usually the last area to clean up on the top face.
Step 5: Flip and do the other side
Turn the slab over so the freshly flattened face is down. If your base is flat, the slab should sit without rocking. If it doesn't, shim it again; don't let the flat face rock.
Reset the rails if needed, set the depth at the high spot, and repeat Steps 3 and 4 until the second face is flat. Because the bottom face is now your reference, the second face comes out parallel to it. Stop as soon as the second face cleans up; every extra pass costs thickness.
Step 6: Sand out the router marks
A router sled leaves small ridges where passes overlap. A random orbit sander takes care of them. Start with a coarse grit to level the ridges, then work up through the grits to the finish you want. Sand the whole face evenly; heavy sanding in one spot leaves a dip that shows under finish.
How much thickness will you lose?
More than most people expect. You lose at least the depth of any cup, plus whatever it takes to get rid of twist and saw marks, on both faces. A badly cupped or twisted slab can lose a lot.
That's why it pays to buy a slab thicker than your finished target. Our page on choosing a slab for a table covers finished thickness, and our pricing page shows how thickness affects price.
Common problems
The slab is flat in the middle but not at the ends. The rails are sagging, or the carriage flexes. Stiffen the rails or support them in the middle.
The surface has a step between passes. The router base isn't square to the carriage, or the carriage tilts. Shim the router base or stiffen the carriage.
The slab moved after a day or two. It wasn't fully dry, or flattening released some stress in the wood. Let it sit, check it with a straightedge after a few days, and take a light final pass if needed.
Tear-out on the live edge. Lighter passes, a sharp bit and slower feed near the edge.
When to hand it off
For more on picking the right slab before you flatten it, see why slabs crack and cup and our FAQ.
Ask About a Slab
Tell us the finished size you're aiming for and we'll help you pick a slab with enough thickness to flatten and still hit it.