COLUMBIA
LIVE EDGE SLABS
Get a Quote

Missouri Slab Woods Compared

The best wood for a live edge slab depends on the job. Black walnut is the favorite for dining tables, white oak is the toughest common choice for bars and busy tables, sycamore gives the widest slabs for the money, and cherry suits smaller, finer pieces. This page compares the woods that grow in mid-Missouri as slabs, not as lumber: how they look, how hard they are, how much they move and what they cost.

Slab woods side by side

Species Color Hardness Movement as it dries Typical width from local trees Price tier (national range, not our price)
Black walnut Chocolate to purple-brown heart, pale sapwood Medium Low, among the more stable Medium Highest: $10–$25 per bf
White oak Light tan to olive-brown Hard Moderate to high; slow to dry Medium to wide Middle: $6–$12 per bf
Red oak Tan with a pink or red cast Hard Moderate to high Medium to wide Below white oak
Cherry Pinkish when fresh, darkens to red-brown Medium Low to moderate Narrow Middle: $6–$12 per bf
Maple Cream to light tan, sometimes spalted Soft maple medium-soft; hard maple hard Moderate Medium to wide Lower: $4–$10 per bf
Sycamore Pale tan to light brown, fine fleck Medium High; prone to warp Wide Lower: $4–$10 per bf
Ash Light cream to tan, oak-like grain Hard Moderate Medium Lower: $4–$10 per bf
Elm Light to reddish brown, wild figure Medium High; interlocked grain twists Medium to wide Lower: $4–$10 per bf
Eastern red cedar Red to purple heart, cream sapwood Medium, with many knots Low Narrow Lowest: $3–$6 per bf

Price tiers use national per-board-foot figures for dried slabs. Green slabs usually sell for roughly half. See slab prices for the per-species figures and a size calculator.

Hardness here is for everyday use: how easily a tabletop dents. Movement is how much a slab tends to shrink, cup or twist as it dries and as the seasons change indoors.

The species, one by one

Black walnut

Walnut is the slab most people picture: dark brown heartwood, a creamy band of sapwood along the live edge, and a figure that gets wild near crotches and burls. It's stable for its size, carves and sands easily, and takes an oil finish beautifully. It's also the most expensive. Wide, clear walnut without much sapwood brings the highest prices, and a crotch figure adds more. According to the Missouri Department of Conservation, Missouri has more black walnut trees than any other state, so this is home ground. See finishing a walnut slab for oil, hardwax oil and polyurethane.

White oak

White oak is heavy, hard and tight-grained. Its pores are plugged, which is why it's the traditional barrel wood and why it handles spills better than red oak. Cut near the center of the log, it shows ray fleck, a ribbon-like figure. The catch is drying: thick white oak is slow to dry and checks if it's rushed. For bars, kitchen islands and tables that see hard use, it's hard to beat.

Red oak

Red oak looks like white oak at a glance, with a pinker cast and coarser, open pores. Those open pores soak up finish and water, so red oak belongs indoors and needs a good sealing finish. It's usually priced below white oak.

Cherry

Cherry starts out pale pink and darkens to a warm red-brown with light, noticeably within the first months. Sapwood stays lighter, so a cherry slab with a sapwood edge has strong contrast. Cherry trees tend to be smaller, so slabs run narrower. They suit desks, benches, shelves and small tables.

Maple

Most maple slabs from yard trees are soft maple, especially silver maple, a common yard tree around Columbia. It's lighter in color and weight than hard maple and dents more easily. Maple slabs are prized when they have spalting (dark lines left by fungus) or streaks left by ambrosia beetles. Spalted wood should still be sound when you press it; soft, punky areas need stabilizing or cutting out.

Sycamore

Sycamore trees grow big along rivers and creeks, so they often give the widest slabs. Sawn through the center, sycamore shows a fine, speckled fleck sometimes called lacewood. It moves more than most woods as it dries, so dryness matters more with sycamore than with almost anything else. A dry, flat sycamore slab makes a wide, light table for much less than walnut.

Ash

Ash has oak-like grain in a lighter color, and it's hard and tough. Many ash slabs now come from trees killed by emerald ash borer. MDC reported the borer in 89 Missouri counties and the City of St. Louis as of 2021 and says it kills more than 99 percent of the ash trees it attacks (MDC). The larvae feed just under the bark, so their tracks stay near the surface and the wood inside is still good slab wood. Supply of large ash will shrink as the remaining trees die.

Elm

Elm's grain interlocks, which makes it hard to split and gives it a feathered, swirling figure. The same grain makes it twist as it dries, so an elm slab needs to be fully dry and flattened before it's built into anything. Dry and finished, it's an underrated table wood.

Eastern red cedar

Cedar has red to purple heartwood with cream sapwood, a strong smell and plenty of knots. The trees are small, so slabs are narrow, and the knots make a busy surface. It's a good choice for shelves, benches and small tables rather than dining tops. Its red color fades toward brown in sunlight unless the finish has UV protection.

Less common: hickory, hackberry, honey locust and osage orange

These turn up from local trees now and then. None is a mainstream slab wood, but each has its fans.

  • Hickory. Very hard and heavy, with strong contrast between light sapwood and brown heart. It moves a lot as it dries and is tough on tools. Good for benches and rustic tables.
  • Hackberry. Pale and plain, and prone to blue-gray stain if it isn't sawn and dried quickly. Inexpensive and fine for painted or simple projects.
  • Honey locust. Reddish-brown heartwood with yellow sapwood. Hard and handsome, and seldom seen for sale.
  • Osage orange. Bright yellow-orange, darkening to brown over time. Extremely hard and rot-resistant. Trees are small and crooked, so slabs are short and narrow, best for small tables, shelves and accents.

Which wood for which project

  • Dining table: walnut for the classic look, white oak for durability, sycamore for width on a budget. See choosing a slab for a table.
  • Coffee table or desk: walnut, cherry, spalted maple or elm, where figure matters more than size.
  • Bar top, island or vanity: white oak first. Walnut and ash also work with a good finish. Avoid red oak near water. See bar tops and countertops.
  • Floating shelves and benches: cedar, cherry, ash or offcuts of anything.
  • Epoxy river table: walnut or another species with a strong edge and contrast. See choosing a slab for an epoxy river table.
  • Outdoors: white oak, osage orange and eastern red cedar heartwood resist rot best, though no slab lasts long in the weather without care.

Whatever the species, a slab that isn't dry will keep moving. Our guide on why slabs crack and cup explains what to expect and which cracks matter.

Ask About a Slab

Name the project and the woods on your shortlist, and we'll suggest which one suits it.

Ask About a Slab

MAKE ROOM FOR SOMETHING ORIGINAL

Your next project
starts with a slab.

Tell us the size, the wood and what you have in mind.

Get a Quote