COLUMBIA
LIVE EDGE SLABS
Get a Quote

Slabs for Bar Tops, Islands and Shelves

A live edge bar top or countertop needs a long, straight, fully dry slab of a hard wood, sealed well on every face. White oak is the first choice for anything near water, with walnut and ash close behind. Below: how long a slab from local logs can be, which species hold up, how thick to go and how far it can hang over, and how to finish it for a wet area.

Lengths available from local logs

A slab can only be as long as the log it came from. Sawlogs are usually cut to lengths between about 8 and 16 feet, with a few inches extra for trimming. A straight, clear trunk long enough for a 12-foot bar is less common than one for an 8-foot table, so long bar slabs cost more per board foot.

If your bar is longer than any single slab, there are two good answers. Join two slabs end to end at a corner or a natural break, like where a bar turns, or use one slab for the main run and a second for the return. Ask us for slabs from the same log so the color matches.

Common sizes to plan around (guidelines, not rules):

Use Common height Common depth
Kitchen counter or island 36 in 25 in for a counter; islands vary
Bar top 42 in 12–20 in
Bathroom vanity 30–36 in 18–22 in
Floating shelf n/a 8–12 in

Species that take abuse

Bars and counters take spills, hot mugs, keys and elbows. The wood needs to be hard, and for wet areas, tight-pored.

  • White oak. The best common choice. Hard, heavy and tight-pored, so it handles spills better than any other common local wood.
  • Black walnut. Medium-hard and the most striking. Fine for a bar or island with a durable finish; it shows dents more than oak.
  • Ash. Hard and tough, with grain much like oak but paler. A good value for long counters.
  • Hard maple. Very hard and pale. Soft maple dents more easily.
  • Hickory. Very hard; rustic contrast. It moves a lot, so it must be fully dry.

Use with care: red oak has open pores that wick water, so keep it away from sinks. Sycamore and elm are wide and attractive but move more, which matters on a long, fixed counter. Cedar is too knotty and soft-faced for a working counter but makes good shelves.

Our slab species comparison compares all of them.

Thickness and overhang

Thickness. Most live edge bar tops and counters finish around 1½ to 2½ inches thick. Thicker looks more substantial and spans farther without support; thinner is lighter and cheaper. Buy rough slabs thicker than the finished size, since flattening takes some off.

Overhang. Seating usually wants about 15 inches of overhang at counter height (36 in) and about 12 inches at bar height (42 in). A thick, hard slab can carry some overhang on its own, but long or deep overhangs need hidden steel brackets or corbels. How far a slab can safely reach depends on its thickness, species and how it's fastened, so have your builder size the supports for your top.

Fastening. A slab keeps moving across its width with the seasons. Fasten it with slotted holes or clips that let it move, never glue it solid along the full width, and leave a small gap where it meets a wall.

Dryness. A counter in a heated, air-conditioned house will keep drying until it settles near indoor moisture, so build only with a dry slab. A slab built into a counter before it's dry enough is the usual reason for a split or a gap at the wall later. See how to check if a slab is dry.

Finish for wet areas

Around a sink or a bar, the finish does most of the work.

  • Film finishes (polyurethane, conversion varnish, bar-top epoxy) give the most water protection. Bar-top epoxy is the toughest against spills but looks like a thick, glossy coat.
  • Hardwax oils look and feel more natural and are easy to touch up, but need re-coating more often in wet areas.
  • Plain oil is the least protective. Fine for shelves, not for a sink edge.

Whatever you use, seal every face and the ends, including the underside, so the slab takes on and gives off moisture evenly. Unequal sealing is a common cause of cupping. For more on oils versus film finishes, see finishing a walnut slab; the same choices apply to other species.

Cut a sink opening only in a fully dry slab, and seal the cut edges well, since they sit next to standing water.

Floating shelves from offcuts

Floating shelves are the easiest live edge project and the cheapest way to get the look. They don't need wide or long pieces, so they're often cut from the narrow ends of slabs, short slabs or offcuts.

  • Size. Most run 8 to 12 inches deep and 24 to 60 inches long.
  • Thickness. About 2 inches looks right and gives room for the mounting hardware.
  • Mounting. Hidden steel rods or a bracket fastened into the studs. A deep shelf loaded with dishes needs serious support.
  • Species. Anything goes. Cedar, cherry and walnut are popular; a matched set from one slab looks best.

Browse the slabs page, and use the pricing page to estimate what a bar-length slab costs before you ask.

Ask About a Slab

Send us the finished length and depth, the use (bar, island, vanity or shelves) and your favorite wood. We'll come back with long slabs that suit the job.

Ask About a Slab

MAKE ROOM FOR SOMETHING ORIGINAL

Your next project
starts with a slab.

Tell us the size, the wood and what you have in mind.

Get a Quote