The best slab for a river table is a dry pair from the same log, with live edges that look good facing each other, solid wood right up to those edges, and enough length and thickness to finish at your size. Dryness matters more than species. Epoxy doesn't stop wood from moving, so a slab that's still drying will pull away from the river or crack beside it.
Here's what to look for, how to size the slabs, and how to estimate the epoxy.
Start with dry wood
A river table puts two very different materials side by side. Cured epoxy barely moves with humidity. Wood shrinks and swells across its width as it gives up or takes on moisture. If the slab is still drying when you pour, the wood keeps shrinking after the epoxy has set. The usual results are a crack beside the river, a gap at the glue line, or a top that cups.
Moisture in the wood can also cause trouble with the pour itself, so check the epoxy maker's guidance on wood moisture.
For furniture used indoors in Missouri, aim for a slab that's close to 6 to 10 percent moisture content, the range MU Extension gives for interior wood here (MU Extension G5507). Our guide on how to check whether a slab is dry explains how to verify it.
One slab or two
A river needs two live edges facing each other. You can get them three ways.
Two sequential slabs from one log. Slabs cut one after another from the same log have nearly the same grain, color and outline. Flip one over and open them like a book (a bookmatch), or set them side by side. This is the classic river table.
One wide slab ripped down the middle. Cut along the grain, then turn the halves so the live edges face each other in the middle. The grain and color match perfectly. You lose the width of the saw cut and you need a slab wide enough for two halves.
Two unrelated slabs. Possible, but color and grain rarely match well. Most builders avoid this unless the contrast is the point.
When you ask for slabs, ask for sequential cuts from the same log. That one request does more for the finished table than any other choice.
Look hard at the live edges
The river is shaped by the two edges. Look for:
- Edges with character. Curves, bulges, crotches and knots make the river worth looking at. Two straight edges make a straight river.
- Edges that work together. Lay the slabs side by side and look at the gap. A river that's wide in some places and narrow in others is more interesting, but very narrow spots can be hard to fill cleanly.
- Sound wood at the edge. Bark doesn't belong under epoxy; it tends to come loose. Plan to strip it and clean down to firm wood. Soft, punky or insect-damaged wood along the edge also has to come off, so judge the edge by the solid wood under it.
Our guide on keeping the bark on a live edge explains why bark should come off before a pour.
Check for cracks and voids
Cracks and knot holes in the slabs can be filled during the pour, which many builders like. Make sure any crack has stopped moving first. A crack that runs into the river edge can let epoxy leak through to the bench if you don't seal it. See bow ties, epoxy fills and other ways to stabilize a split.
Shake, where a growth ring has separated, is harder to deal with than an ordinary crack. Our guide on why slabs crack and cup explains the difference.
Size the slabs to the table
Length. Buy slabs longer than the finished table so you can trim checked ends square. End checks are normal on air-dried slabs.
Width. Finished width is the two slab widths (after trimming the edges back to sound wood) plus the river. For example, two 15-inch slabs and a 6-inch average river make a 36-inch-wide top. Common dining tables run about 36 to 42 inches wide, and it's usual to allow roughly 24 inches of edge for each person seated. For seating and size charts, see choosing a slab for a table.
Thickness. Buy thicker than your finished target. You'll lose thickness flattening both faces, and the river is flattened along with the wood. See flattening a slab with a router sled for how much that can take.
Match the slab to the epoxy
Thick slabs mean deep pours. Epoxy comes in thin "coating" or tabletop formulas and thicker "deep pour" or casting formulas. Every product has a maximum pour depth per layer, and going past it can make the epoxy overheat, crack or yellow. Check the product's maximum pour depth before you buy the wood. If the slab is thicker than one pour allows, you'll pour in layers, letting each one cure according to the label.
Also seal the wood before the main pour. A thin seal coat of epoxy brushed onto the live edges and any cracks helps stop air in the wood from bubbling up into the river.
Estimate how much epoxy you need
Work it out in cubic inches and divide by 231, the number of cubic inches in a US gallon.
Length × average river width × depth = cubic inches. Cubic inches ÷ 231 = gallons.
Example: a river 72 inches long, averaging 6 inches wide and poured 2 inches deep.
- 72 × 6 × 2 = 864 cubic inches
- 864 ÷ 231 = about 3.7 gallons
Buy more than the math says. Some epoxy soaks into the wood, some stays in the mixing buckets, and molds can leak. Add the volume of any cracks and knot holes you plan to fill, too.
Which species work
Almost any dry hardwood can make a river table. The choice is mostly about looks:
- Dark woods such as walnut stand out against clear, blue, white or metallic rivers.
- Pale woods such as maple, ash and sycamore pair well with dark or black rivers.
- Woods with strong figure, like spalted maple or crotch wood, can carry a simple clear river.
Our page comparing Missouri slab species covers color, hardness and how each species moves.
Questions to ask the seller
- Are these slabs from the same log, and were they cut in sequence?
- What do they read on a moisture meter, and when was that taken?
- How much of the live edge is sound once the bark is off?
- Are the cracks stable?
- How thick are they now, and are they rough or flattened?
For what slabs like these cost, see our pricing page, or browse our slabs page.
Ask About a Slab
Tell us the finished length and width you want, how wide a river you have in mind and when you're building. We'll tell you which slabs could work.