COLUMBIA
LIVE EDGE SLABS
Get a Quote

How to Check Whether a Slab Is Dry Before You Buy It

Take moisture readings in several places on both faces, away from the ends, and compare them with where the slab will live. For furniture used indoors in Missouri, that's about 6 to 10 percent moisture content. Then back the numbers up with the slab's history: when it was sawn, how it was stored, and when the readings were taken. One good reading on one spot doesn't prove a slab is dry.

Here's what to check, in the order we'd check it.

Know the number you're aiming for

Wood takes on and gives up moisture until it matches the air around it. Air-dried wood in Missouri still holds more moisture than wood that has settled indoors (6 to 10 percent, per MU Extension G5507).

That gives you three rough bands for a slab:

  • Well above 14 percent: still drying. Expect it to shrink and move.
  • Around 12 to 14 percent: air-dried, the range MU gives for air-dried lumber in Missouri. Good for many uses, but it will keep drying and shrinking a bit once it's indoors.
  • Around 10 to 12 percent: drier than air-dried; let it settle indoors and recheck.
  • Around 6 to 10 percent: close to what it will settle at inside a home.

The slab drying time guide explains why air-dried and indoor-dry aren't the same thing.

Which meter, and what it's telling you

You don't need an expensive meter to shop for slabs, but you should know what each type is telling you.

Pin meters push two metal pins into the wood and measure how easily a small current passes between them. Wetter wood conducts better. They read at the depth the pins reach, and they leave two small holes. Pin meters need the right species setting or correction chart, and their readings shift with the wood's temperature, so a slab in a cold barn can read differently than the same slab in a warm shop.

Pinless meters press a flat pad against the surface and read a fixed depth below it, with no holes. They need a flat, clean spot and the right species or density setting. A rough-sawn surface, a band-saw ridge or a gap under the pad can throw the reading off.

Either type is fine for a buyer. What matters more is reading in the right places and reading more than once.

Where to take readings

Stay away from the ends. End grain loses water much faster than the faces, so the ends of a slab often read drier than the middle. A seller who only meters the ends is giving you the best-looking number.

Take readings along the length. Check near one end, the middle and the other end, at least.

Check across the width. Read near the center of the slab and near each edge. On a slab that includes the pith, read near it too.

Check both faces. The top of a stack and the bottom can dry differently, and so can the two faces of one slab.

Look for the spread. If every reading lands within a couple of points, the slab has dried fairly evenly. A big gap between spots means part of the slab is still wetter than the rest.

Remember the surface dries first

A slab dries from the outside in. The surface drops below the point where wood starts to shrink while the center can still be quite wet, as the USDA Forest Products Laboratory explains in its Wood Handbook chapter on moisture and wood. Most meters only read the outer part of a thick slab.

So on a 10/4 or 12/4 slab, a dry surface reading is a good sign but not proof. That's where the slab's history matters: a thick slab sawn a few months ago can't be dry all the way through, no matter what the surface says.

Other things to check in person

A meter isn't the only clue.

End checks. Small cracks at the ends are normal on air-dried slabs. Look at whether they look old (gray, dusty, weathered inside) or fresh (bright, clean wood inside). Fresh cracks suggest the slab is still drying. Our guide on why slabs crack and cup covers which cracks matter.

Weight. Green wood is heavy with water. Two slabs of the same species and size can feel very different. If you're buying a slab to finish later, weigh it on a bathroom scale and weigh it again a few weeks later. If it keeps getting lighter, it's still drying. When the weight holds steady, it has caught up with the space it's stored in.

Sticker shadows. Slabs dried in a stack sit on thin spacer strips called stickers. Faint stripes across the face where stickers sat tell you the slab was stacked to dry with air around it, which is a good sign about how it was handled. Stripes don't tell you how dry it is. Some sticker marks are only on the surface and sand out, and some go deeper, so ask before you count on a stripe-free face.

The surface. A slab that feels cool and damp, shows mold, or has sap weeping from it is not dry. Wet, loose bark is another sign of a slab that's still drying.

Cupping and twist. Lay a straightedge across the width. A slab that has already cupped has done some of its moving, which isn't a bad thing as long as it's dry. A slab that's dead flat right off the mill hasn't been tested yet.

Ask for readings and dates

Ask the seller:

  1. What does it read, and when was that taken?
  2. Where on the slab did you measure?
  3. What meter, and what species setting?
  4. When was it sawn, and how has it been stored since?
  5. Is it air-dried or kiln-dried? If kiln-dried, when did it come out?

A seller who keeps readings with dates can show you how a slab has dried over time. That's worth more than any single number.

Red flags

  • Readings only from the ends
  • A thick slab sawn recently but sold as "dry"
  • No date on the reading, or "it's been drying a while"
  • Fresh, bright cracks still opening
  • Mold, wet bark or sap
  • A seller who won't let you meter it

None of these mean you shouldn't buy the slab. Green and partly dried slabs are good buys if you have time and space to let them finish. They just shouldn't be priced or sold as dry.

If the slab isn't dry yet

You can still buy it. Price should reflect it, and our pricing page explains how dryness moves the price. Just don't flatten or finish it until a meter says it has caught up with where it will live.

For more on what slabs are used for and what size you need, see choosing a slab for a table and our FAQ.

Ask About a Slab

Tell us the project and your deadline, and ask us anything about how a slab has dried.

Ask About a Slab

MAKE ROOM FOR SOMETHING ORIGINAL

Your next project
starts with a slab.

Tell us the size, the wood and what you have in mind.

Get a Quote